Lightweight

SCCA Compliant as of 2022 - Lightweight Aluminum Pressure Plate - 7 lb weight reduction from original Pressure plate Recommended to Use - Pressure Plate Bolt Kit Torque Specs:  24 ft-lb

Read more less

RaceCar Application: FM FM - this is the lightweight option to replace the original which is no longer available. Replacing all (8) caliper pucks equals a 1.1 lb reduction in weight. Wilwood’s exclusive Thermlock Pistons provide the most effective thermal barrier available for minimizing heat transfer from the brake pads to the caliper body, seals and fluid. This innovative multi-part design incorporates a stainless steel shield and coated aluminum shell configuration that effectively retards heat transfer by at least 25 percent. This reduction in operating temperature eliminates seal crystallization and localized fluid boiling, which decreases distortion in the caliper body and piston bores, extending overall service life.  

Read more less

RaceCar Application: FMzR + FM FM - this is the lightweight option to replace the original 060-129. Replacing all (4) CV Joints (060-717) and CV Boots (060-718) equals a 2.85 lb reduction in rotating mass. GKN Motorsport S10 aerodynamic Fast Boot, with a zinc passivated steel outer and heavy duty rubber inner aero boot. TO BE USED WITH: 060-717 CV Joint - Lightweight

Read more less

Braille 12v 6a lithium charger/maintainer charges at a reasonably quick 6 amps and is designed to maintain & keep Braille lithium batteries fully charged when not in use or sitting for long periods of time. In the case that a Braille lithium battery is every fully discharged (10 volts is considered 0% state of charge on a 12v lithium battery), this charger does have a "pre-charge/revival mode" that will do a slow "pulse charge" as long as the battery has at least 2 volts (to know that it is connected to a battery) and will slowly bring it back up to 10 volts before charging at the standard 6 amp rate back up to full. This updated charger now comes with an SAE quick disconnect end along with a ring terminal harness and standard battery clamps for more charging solutions in a variety of vehicles, bikes, etc. (Power cord included, but not pictured)  

Read more less

RaceCar Application: FM FM - this is the lightweight option to replace the original 030-139. Installing the Aluminum Belly Pan equals a 22 lb reduction in weight.

Read more less

RaceCar Application: FMzR + FM FM - this is the lightweight option to replace the original 060-128. Replacing all (4) CVs and CV Boots (060-718) equals a 2.85 lb reduction in rotating mass. GKN Motorsport size 10 94mm lightweight CV joints. These plunging constant velocity joints feature a 94mm OD and and have been developed by GKN Motorsport to ensure easy rotational liner motion at for wheel or differential applications. With over 30 years of continuous development of GKN Driveline products, these GKN Motorsport plunging CV joints offer a significant weight reduction, cooler running temperatures and enhanced joint life through higher performance. TO BE USED WITH: 060-718 GKN CV Fast Boot

Read more less

At only 4.5 pounds, the GreenLite G20. The Braille Lithium Charger/Maintainer (sold separately) should be used in vehicles that are not driven regularly to offset parasitic draw. BENEFITS: • Quicker starting (a full volt higher than lead and less voltage drop during cranking)• Less horsepower draw from the alternator due to efficient charging (5 times faster than lead)• Can be used in "Total Loss" (no alternator) applications• Improved engine management & data logging performance (more stable voltage)• Lasts 3-5 times longer (especially under the harshest environments)• Much more reliable (less than 0.5% failure rate)• Significant weight savings. (up to 1/4 the weight)• Don’t self-discharge, so if the battery is disconnected (no draw or via power disconnect switch), they can sit for over a year and still have over 13 volts to start the vehicle.To get all these benefits in one simple step makes it a very cost effective upgrade!!

Read more less